All models

Liberty Bell: Step-by-step building instructions

An original build inspired by the Liberty Bell, a gold bell with its famous dark crack hanging from a heavy wooden yoke on a black stand, on a stone floor with a low rope barrier, a plaque and planters.

105 parts 14 steps Beginner

Liberty Bell assembled model

Loading 3D model Check your connection and try again.

Drag to rotate. Pinch or scroll to zoom.

Build steps

Finished model

Drag to look around, then build it in 14 steps.

Step 1 of 14

  1. Step 1 · 5 pieces

    • Plate 4 x 4 Light Bluish Grey 3031 1×
    • Plate 4 x 6 Light Bluish Grey 3032 1×
    • Plate 4 x 8 Light Bluish Grey 3035 1×
    • Plate 6 x 8 Light Bluish Grey 3036 1×
    • Baseplate 16 x 16 Dark Bluish Grey 3867 1×

About this build

Few objects in Philadelphia draw a queue like this cracked bronze bell. The Liberty Bell hangs from its old wooden yoke, and the jagged crack running up from its lip is what everyone recognizes. That crack is the first thing this build gets right: on the front face of the gold bell, black 1×1 bricks zig-zag up the two lower waist courses, and a black round tile carries the line onto the lip.

The bell is built from the top down. A 2×2 round brick forms the crown, a 4×4 cone gives the sloping shoulder, and a round plate marks the band near the top. Below that come three square courses with round 1×1 corners, finished by a 6×6 round plate as the flared lip. Nothing under the bell holds it up: every piece clips into the one above, so it hangs a couple of plates clear of the floor, just as the real bell hangs from its yoke.

The yoke is a stepped stack of dark brown bricks with sloped ends and a ridge on top, held by black tiles at the ends and gold round tiles as bolts. Two black posts with angled feet carry it. Around them sit a light grey stone floor with a pale paving square under the bell, a low barrier of black posts with dark red rope, a small gold plaque and four potted shrubs.

At a glance

  • 105 parts in 14 steps on a 16×16 baseplate
  • Bell 6 studs wide at the lip
  • About 30–45 minutes for most builders

Step 8 is the one to watch: the crown has to go under the exact centre of the yoke, or the bell will hang off centre. For a variation, leave out the back barrier to open the view.

Step 1 of 14

Every piece is a standard LEGO® element, listed with its LDraw part number and color.

Parts list
PartName / IDColorQty
Brick 1 x 23004 Black 7
Brick 1 x 13005 Black 2
Plate 1 x 23023b Black 2
Slope Brick 45 2 x 13040b Black 4
Brick 1 x 1 Round with Hollow Stud3062b Black 8
Tile 1 x 2 with Groove3069b Black 2
Brick 1 x 2 x 2 without Understud3245c Black 4
Plate 1 x 63666 Black 2
Tile 1 x 1 Round with Groove98138 Black 1
Plant Flower 2 x 2 Leaves4727 Green 4
Plate 4 x 43031 Light Bluish Grey 1
Plate 4 x 63032 Light Bluish Grey 1
Plate 4 x 83035 Light Bluish Grey 1
Plate 6 x 83036 Light Bluish Grey 1
Brick 2 x 2 Round without Reinforcement3941 Light Bluish Grey 4
Tile 2 x 2 with Groove3068b Dark Bluish Grey 1
Baseplate 16 x 163867 Dark Bluish Grey 1
Tile 2 x 2 with Groove3068b Very Light Bluish Grey 10
Tile 1 x 2 with Groove3069b Very Light Bluish Grey 2
Plate 6 x 6 Round with Hole and Snapstud11213 Pearl Gold 1
Brick 1 x 23004 Pearl Gold 10
Brick 1 x 13005 Pearl Gold 2
Slope Brick 45 2 x 13040b Pearl Gold 2
Brick 1 x 1 Round with Hollow Stud3062b Pearl Gold 12
Brick 2 x 2 Round without Reinforcement3941 Pearl Gold 1
Cone 4 x 4 x 2 with Axlehole3943b Pearl Gold 1
Plate 4 x 4 Round with Hole and Snapstud60474 Pearl Gold 1
Tile 1 x 1 Round with Groove98138 Pearl Gold 4
Brick 2 x 62456 Dark Brown 3
Brick 2 x 43001 Dark Brown 1
Brick 2 x 23003 Dark Brown 2
Slope Brick 45 2 x 23039 Dark Brown 2
Slope Brick 45 2 x 4 Double3041 Dark Brown 1
Tile 1 x 4 with Groove2431 Dark Red 4
Total pieces105